Dishwasher Troubleshooting: Fix Common Problems

Last updated: October 8, 2026

Dishwasher problems almost always fall into a few familiar buckets: it will not start, it will not drain, dishes come out dirty or wet, it leaks, or it makes a noise it never used to make. Work through the checks below in order. Most of the time the answer is simpler than you feared.

Will not start

  • Door not fully latched: push the door firmly until you hear the click. No latch, no cycle, no exceptions.
  • No power: check the circuit breaker, and look for a wall switch or switched outlet under the sink that feeds the dishwasher.
  • Control lock is on: a lock icon on the panel means child lock. Hold the lock button for about 3 seconds to release it.
  • A cycle got interrupted: press and hold Start/Cancel for 3 seconds to reset, then pick a fresh cycle.

Standing water / will not drain

  • Clogged filter: twist the cylindrical filter out of the tub floor, rinse it under hot water, and pull out the trapped food.
  • Kinked drain hose: if you can reach behind the unit, check the hose for sharp bends that choke the flow.
  • Blocked air gap or disposal connection: pop the little air-gap cap next to the faucet and clean it. If a garbage disposal was recently installed, its dishwasher inlet knockout plug may still be in place, which blocks draining completely.

Dishes are not clean

  • Spray arms cannot spin: a tall pan can stop the arm mid-rotation. Reload so nothing touches the arms, and clear the small holes with a toothpick.
  • Water not hot enough: run the kitchen tap until the water runs hot before starting the cycle. Older dishwashers barely heat their own water.
  • Pre-rinsing too well: modern detergent needs some food soil to work against. Scrape the plates; do not wash them first.
  • Stale or skimpy detergent: old detergent loses strength. Use fresh automatic-dishwasher detergent and fill the dispenser to the line.

Dishes are not drying

  • Rinse aid is empty: refill the dispenser. Rinse aid does more for drying than most people expect.
  • Heated dry is off: energy-saving modes often disable it. Turn it back on for plastic-heavy loads.
  • Unloading order: unload the bottom rack first, so water pooled on top-rack items does not drip onto dry dishes below.

Leaking water

  • Wrong soap: the number-one cause of dishwasher leaks is regular liquid dish soap. Only use detergent labeled for automatic dishwashers.
  • Dirty door gasket: wipe the rubber seal around the door. Trapped food or a twisted gasket lets water slip past.
  • Rinse-aid spill: wipe up spills around the dispenser; they foam over during the cycle.
Safety warning: If water is actively leaking onto the floor, turn off the water supply valve under the sink and switch the dishwasher off at the breaker. Leaks that keep coming back need a technician. Water and electricity are a dangerous combination.

Strange noises or smells

  • Grinding or rattling: usually a spray arm hitting a dish or debris in the filter. Stop the cycle and look before running it again.
  • Musty smell: clean the filter, then run an empty cycle on the hottest setting with a dishwasher cleaner. Leave the door slightly ajar between uses so it dries out.
  • Burning smell: stop the dishwasher immediately, switch it off at the breaker, and call a technician. Do not run it again until it has been checked.

When to call a professional

Leaks that keep returning, burning smells, sparks, error codes that come straight back after a reset, and anything behind the kick plate or involving pumps and wiring belong to a qualified technician. Write down the exact error code before you call. It tells them which part to test first and usually shortens the visit.

Related error codes

Every dishwasher error code we cover, grouped by brand. Each page has the verified meaning and safe fixes:

Bosch dishwasher codes

Frigidaire dishwasher codes

GE dishwasher codes

Kenmore dishwasher codes

LG dishwasher codes

Maytag dishwasher codes

Samsung dishwasher codes

Whirlpool dishwasher codes

Frequently asked questions

How do I reset my dishwasher?

On most models, press and hold the Start or Cancel button for about 3 seconds until it drains and resets. If that does nothing, cut the power (unplug it, or flip its breaker off) for 2 to 3 minutes, then restore it. Your manual has the exact button combination for your model; they vary more than you would expect.

Why is there standing water in the bottom of my dishwasher?

Standing water means it cannot drain. The usual suspects, in order: a clogged filter, a kinked drain hose, a blocked air gap by the faucet, or a knockout plug still in place inside a newly installed garbage disposal. Clean the filter first. It fixes a large share of drainage complaints on its own.

Can I use regular dish soap in my dishwasher?

No. Regular dish soap makes far too many suds, which causes leaks, poor cleaning, and sometimes error codes. Use only detergent labeled for automatic dishwashers, and do not overfill the dispenser. If you already made this mistake, run a rinse cycle to clear the suds before a real wash.

When should I call a technician instead of fixing it myself?

Call a professional for leaks that keep coming back, burning smells, sparks, error codes that return right after a reset, and anything that means opening panels or touching pumps and wiring. If water is actively leaking, shut off the supply valve under the sink first.